Answer
Can the Anker SOLIX C1000 run ResMed AirCurve 10 VAuto BiPAP with HumidAir humidifier?
Runs
Runs. Draw is 23 W, within the 1,800 W continuous output. Estimated runtime on AC: about 23.6 hr, counting about 15 W of inverter draw.
Medical safety notice: Will It Run? gives general power estimates only, not medical advice. Power draw varies by model, settings, pressure, humidifier and altitude. Before relying on any battery, power station, inverter or generator for a medical device, confirm approved power sources with the device manufacturer and your doctor or equipment supplier, and test your setup before an emergency. Never change prescribed settings to extend battery life. If your therapy is life-sustaining, keep the backup your supplier provides, register with your utility's medical-needs program, and have an evacuation plan. Run generators outdoors only, at least 20 ft from windows and doors, because of carbon monoxide risk. In an emergency, call 911.
Check price on AmazonManufacturer pageAs an Amazon Associate we earn from qualifying purchases.
The comparison
| Anker SOLIX C1000 | ResMed AirCurve 10 VAuto BiPAP with HumidAir humidifier | |
|---|---|---|
| Continuous output / running draw | 1,800 W | 23 W |
| Capacity / average draw | 1,056 Wh nameplate, 898 Wh usable | 23 W |
| Runtime on AC | 23.6 hr (23 W + about 15 W inverter draw) | |
| Nights on AC (8 hr) | 3.0 | |
| On DC, best case | Not modeled: ResMed's AirSense 10 guide says to turn humidity off on an external battery, and the Air10 DC converter's 13 A input is above a typical 10 A car port. | |
| Sources | Station source | Appliance source |
How AC runtime is figured: usable Wh (nameplate × 0.85) ÷ (CPAP watts + about 15 W). The 15 W is the inverter's own draw just to stay on: BLUETTI counts about 15 W of self-consumption in its AC180 runtime formula, and an owner test measured about 17.5 W idle on a DELTA 3 Plus. Larger stations can idle higher, so test your own setup before you rely on it. DC figures skip the inverter and are a best case. Method and DC converter limits: CPAP power station guide.
More on the Anker SOLIX C1000 · More on this machine · CPAP hub
Questions
Can the Anker SOLIX C1000 run ResMed AirCurve 10 VAuto BiPAP with HumidAir humidifier?
Runs. Draw is 23 W, within the 1,800 W continuous output. Estimated runtime on AC: about 23.6 hr, counting about 15 W of inverter draw.
How was the runtime calculated?
On AC: 1,056 Wh × 0.85 = 898 Wh usable, divided by (23 W + about 15 W inverter draw) = 23.6 hr. Not modeled: ResMed's AirSense 10 guide says to turn humidity off on an external battery, and the Air10 DC converter's 13 A input is above a typical 10 A car port.
Where did the numbers come from?
Tech specs: 1,056 Wh, LiFePO4, 3,000 cycles to 80%, 1,800 W pure sine wave, 2,400 W AC surge, 6 AC outlets, 28.44 lb. The FAQ says SurgePad is for heat-generating devices when output exceeds the rated output; the 2,400 W figure is the published AC surge. ResMed's therapy-device power table (ResMed Deutschland, Art.-Nr. 1018528/11) lists AirCurve 10 VAuto with HumidAir at 23 Wh during operation. Energy per hour equals average watts, so the average draw is 23 W. ResMed notes the values were measured in a lab and that a local meter can differ.